Blue Robotics

BlueROV2 (Acrylic - 100m)

The Blue Robotics BlueROV2 is the world’s most affordable high-performance ROV. With a 6-thruster vectored configuration, open-source electronics and software, and plenty of expandability, it’s the perfect ROV for inspections, research, and adventuring. What will you see?

BlueROV2 (Aluminum - 300m)

The Blue Robotics BlueROV2 is the world’s most affordable high-performance ROV. With a 6-thruster vectored configuration, open-source electronics and software, and plenty of expandability, it’s the perfect ROV for inspections, research, and adventuring. What will you see? Remember to complete the ROV you will need to add lights and a tether of the length you require and maybe you would like a reel for ease of tether handling, for power you'll need to add batteries and charger, or even upgrade to the OTPS surface supply system- you'll also need a laptop to run the software on - we can help advise on all these and even build it for you if your in need of any assistance.

5V 6A Power Supply

Bar High-Resolution Depth/Pressure Sensors

The Bar series sensors are compact, high-resolution pressure sensors for underwater pressure and depth sensing.

BarXT Extended Submersion Depth/Pressure Sensors

The BarXT series provides accurate underwater depth and pressure sensing for applications that require continuous submersion. These sensors can stay submerged indefinitely with no maintenance. Available in four models for operating depths from 20 to 1000 meters.

Basic ESC

An electronic speed controller (ESC) is necessary to run any three-phase brushless motor like Blue Robotics’ thrusters and motors.

Basic ESC 500 - BlueBoat

Basic ESC 500 - Standard

This bidirectional speed controller is similar to our original Basic ESC, but suited for the high power requirements of the T500 Thruster, even when in a space with poor airflow and cooling, like inside an ROV enclosure. It comes in two versions: a standard version for most applications and a BlueBoat version for use in the BlueBoat USV.

Battery Cell Checker

The Battery Cell Checker plugs into the battery balance plug and tells you cell voltages, overall pack voltage, and overall state-of-charge. It’s a great field tool to check your batteries and make sure they are ready for each dive!

Battery Power Cable Set

Battery power cable set for the BlueROV2 with pre-installed WetLink Penetrators and 5.5 mm bullet connectors.

Binder 770 Bulkhead Connector

This Binder 770 bulkhead connector is our standard for tether connections above the water. This connector can be mounted in a spare hole on the FXTI for your custom connections.

Binder 770 Plug (2.5-4mm)

This Binder 770 connector is our standard for tether connections above the water. Some assembly with soldering required for installation.

Binder 770 Plug (6-8mm)

Bluart USB to Serial and RS485 Adapter

This compact adapter connects to USB and provides a TTL serial port or RS485 serial port connection. Recommended for use with the Ping Sonar.

BlueBoat BaseStation

The BaseStation is a wifi radio access point for the BlueBoat with a 2.4 Ghz MikroTik radio, internal battery and charge management, and USB-C connectivity. You can connect directly over USB-C or connect your device to the access point to connect with your BlueBoat.

BlueBoat Battery Splitter Cables (SPLITTER-CABLE-VP)

These cables allow multiple batteries to be connected for discharge, charge, and balancing. Internal fuses prevent overcurrent, but this product must be used with extreme caution and a knowledge of lithium ion batteries. Only connect identical batteries at the same charge and balance state! Please use this product with caution and read the instructions to avoid risk of fire and injury!

BlueBoat Hull Mount Bushings (6 pcs)

These bushings are important when fastening to the mounting holes at the bottom of the BlueBoat hull. Conforming to the shape of the hull, they distribute the load and help to secure your payload.

BlueBoat Uncrewed Surface Vessel

The BlueBoat is the planet’s most affordable robotic surface vessel. With an innovative hull design, endless expansion possibilities, and open-source BlueOS software, it’s the ideal platform for hydrographic surveys and robotics system development.

BlueOS MicroSD Card - Configured with AdruSub

This 128 GB micro SD card is preloaded with BlueOS for the Raspberry Pi computer. It can be configured for the BlueROV2 or BlueBoat and can be used with the Navigator Flight Controller or any ArduPilot compatible controller!

BlueROV2 Electronics Enclosure (Acrylic - 100m)

Pre-assembled and tested with the BlueROV2 electronics, this enclosure is ready-to-integrate into your custom ROV frame or other application. It includes the 18-hole end cap with nothing installed. At minimum, we recommend including a Pressure Relief Valve, a pressure sensor like the Bar30 Pressure/Depth Sensor and the Power Cable Set to connect to a battery enclosure.